crevis

M9289

Ethernet TCP/IP NETWORK ADAPTER


제품비교 담기

도움이 필요하세요?

샘플요청 견적문의
썸네일이미지 원본

주요특징


- 통신 이중화 듀얼타입 네트워크 어댑터를 통해 “Active – Standby “ 방식으로 통신 이중화 구현 , Active 모듈 문제 발생 시 , Standby 모듈이 즉시 동작하여 안정적인 통신을 유지 가능

- 파워 이중화 전원 문제 발생 시 외부 노이즈로부터 통신, 네트워크를 보호하고 전원 문제 시 발생할 수 있는 손실을 방지

 - 핫스왑 Backbone 구조로 인해 전원이 인가된 상태에서도 모듈 착탈이 가능하며, 유지보수 시에도 설비 멈춤없이 안정적 유지 보수 및 교체 가능
M9289 (Ethernet TCP/IP NETWORK ADAPTER)

Adapter Type

Slave node (Ethernet TCP/IP), Single
Protocol MODBUS/TCP,MODBUS/UDP,Ethernet/IP, CC-Link IE Field Basic
Sub-Protocol HTTP,DHCP,10 TCP Connections, SLMP
Max. Expansion Module 63 slots
Max. Data Size(Input + Output) Max 128 bytes each slot
Max Length Bus Line Up to 100m from Ethernet Hub/Switch with twisted CAT5 UTP/STP
Max. Data Size(RX, RY) each 32 bytes (4 Stations occupied)
Max. Data Size(RWr, RWw) each 256 bytes (4 Stations occupied)
Max. link points per station (RX, RY) each 64 points
Max. link points per station (RWr, RWw) each 32 points
Max. Nodes Limited by Ethernet Specification.
Baud Rate 10/100Mbps, Auto-negotiation, Full duplex
Interface Connector RJ-45 socket * 2pcs
IP-Address Setup Via DHCP/BOOTP or IOGuidePro(Crevis Software)
IP-Address Range xxx.xxx.xxx.1 ~ 253 (User area)
IAP Mode When DIP Switch 1 to 8 setting is 254 or 255
(Using only Internet Explorer / recommended version 11 )
Serial Port RS232 for MODBUS/RTU, Touch Pannel or IOGuidePro
Serial Configuration (RS232) Node : 1 (Fixed)
Baud Rate : 115200 (Fixed)
Data bit : 8 (Fixed)
Parity bit : No parity (Fixed)
Stop bit : 1 (Fixed)
Indicators 4 LEDs
1 Green/Red, Module Status (MOD)
1 Green, Cyclic transmission status (D LINK)
1 Green, Exchange Data/Traffic Present LED (ACTIVE)
1 Green/Red, Expansion I/O Module Status (IOS)
2 LEDs (each RJ45 Connector)
1 Yellow, Link/Active
1 Green, Not used
Module Location Starter module left side of M-Series system
General specification (Supplied by M7001)
UL System Power

Supply voltage : 24Vdc nominal, Class 2

System Power Supply voltage : 24Vdc nominal
Supply voltage range : 15~28.8Vdc
Protection : Output current limit, Reverse polarity protection
Power Dissipation Network Adapter : 90mA typical @ 24Vdc
Current for I/O Module 2.0A @ 5Vdc
(If except for NA, current for I/O module is about 1.7A)
Isolation System power to internal logic : Non-isolation
System power I/O driver : Isolation
UL Field Power Supply voltage : 24Vdc nominal, Class 2
Field Power Supply voltage : 24Vdc typical (Max.28.8Vdc)
* Field Power Range is different depending on IO Module series.
Refer to IO Module`s Specification.
Max. Current Field Power Contact DC 10A Max
Torque 0.8Nm(7 lb-in)
Single Wire 0.205㎟ - 1.3㎟ (24-16 AWG)
Weight 179g
Module Size 54mm x 110mm x 75mm

NEWSLETTER

국내유일의 필드버스 전문회사 크래비스의 새로운 소식을 받아보세요!

뉴스레터 신청하기